|
| SDR-IQ SOFTWARE DEFINED RADIO |
 |
SDR-IQ SDR receiver spectrum analyser and panoramic adapter 0.0001-30MHz DSP.
This is a highly compact, yet high performance receiver. It has excellent dynamic range and connects to any Windows or Linux based PC via USB lead. The radio is self powered via the USB connection. Antenna connector is BNC. The unit is supplied with USB lead and full software.
Covers an incredible range of 500Hz - 30MHz. It can also record up to 192kHz of any band segment for later playback and full tuning.
Uses - High performance HF Receiver with 190 KHz realtime Panoramic Adapter
- Ultrasound experimentation (Sonar, Underwater ultrasound, Bat and Insect detectors)
- IR (Infrared) subcarrier detection and communications
- Record up to 190 KHz of spectrum to hardrive for later playback and demodulation
- Panoramic adapter for Communication Receivers (any IF in HF band 455 KHz, 8.83 MHz, 10.7 MHz, 21.4 MHz, etc)
- Very Low Frequency (VLF) Studies
- Spectrum Analyzer backends
- Processor for Radio Astronomy receivers
Features - Smallest SDR with RF DSPTM that samples the whole HF band at once and performs the initial filtering at 67 MHz sample rate with 23 bit accuracy. Uses a high performance Analog Devices 14 bit analog to digital converter
- Sends 16 bits of I/Q Data to the PC via USB. No messy soundcard cables required
- SDR-IQ is USB powered. No power supply is required. Works great with laptops running on batteries.
- Incredible receive performance.
- High resolution spectrum display with higher resolution and speed than those in $10K radios.
- RF preselection filters for great IMD performance.
- Serial port to directly interface with radios like the Icom IC-R8500, IC-R9000, IC-R9500, IC R7000, IC-R7100 and AOR AR-5000.
- 50 ohm RF input that can be easily interfaced to antennas, Ultrasonic transducers, IR detectors, and other RF equipment.
- Open source ActiveX control and ActiveX sample program for easy software customization. SpectraVue (not open source).
- Windows, Linux and Mac OS drivers for developers.
- Network server that allows remoting of the SDR-IQTM. Servers available for both Windows and Linux.
- Adds the best panoramic display features to transceivers like the Yaesu FT1000, FT2000, FT9000 and IC-7800 using the RX output connector or RX loopback
Specification - Frequency Range: 500Hz to 30 MHz in 1 Hz steps. (Usable down to 100 Hz)
- Input Impedance: 50 Ohms
- Clipping RF level (Max Gain): -4dBm (Typ)
- Maximum Frequency display BW: 190 KHz
- Sampling Rate: 66.666 MHz
- I/Q Image Rejection: 80 dB+ (Typ)
- MDS (500 Hz): -127 dBm @ 14 MHz
- Input IP3: 15dBm+ (Typ) * Measured with a dither signal
- Voltage: 5 Volts (USB port powered)
- Current Draw: 425 mA
- Connectors: BNC (RF In), USB 2.0, RS-232 (Serial Bi-directional)
- Indicators: Power (Green), Sample (Yellow), ADC Clip (Red)
- Dimensions: 3.75x3.75x1.25 Inches
- Processor: Atmel AT91SAM7S256 w/ JTAG port.
- Analog Demod: AM, WFM, USB, LSB, N-FM, DSB and CW
- Measurements Functions: IQ vs. Time, Power vs. Frequency, Power vs. Frequency vs. Time 3D Surface, Power vs. Frequency vs. Time Spectrogram, Power in BW vs. Time, IQ Phase
- Max FFT Size: 262144 Point
- Max IQ Recording (All BWs): Unlimited to Hardrive.
- Screen Update Rate: 50 FFTs/sec , 190 KHz SPAN @ 100 Hz RBW
- Window Type: Rectangular, Hanning, Hamming, FlatTop, Blackman, Blackman-Harris
- Displayed Average Noise Level dBm/Hz:-133dBm/Hz TYp. 14.200 MHz
- Worst Case Spurious Carriers (Birdies):-80dBfs , -100dBfs (typ)
|
| |
|
|
|
| Model: 10 |
|
| Price: £539.95 |
|
| |
|
|
|
