• You will receive 20 Watts for submitting a review
Login to earn Watts for sharing!

Anan-10EE HF + 6M 10W All Mode Transceiver

SKU:
10-980

More Views

Anan-10EE HF + 6M 10W All Mode Transceiver
SKU:
10-980
Category:
Transceivers
Manufacturer:
Anan

The Anan10EE is almost identical to the Anan 10E with a smaller ADC (Analogue to Digital Converter).

£1,294.99

Out of Stock

You'll earn 1079 Watts for this item
Details
Reviews

The New Anan 10EE is here!! The Anan10EE is almost identical to the Anan 10E with a smaller ADC (Analogue to Digital Converter). In simple terms, this means you have the capabilities to use 2 receivers at the same time on the Ana 10B opposed to 7 receivers as is the case with the Anan 10E. Other differences between the ANAN-10E & the ANAN-10B are below: 1. The ANAN-10EE uses a 14 bit ADC while the ANAN-10E uses a 16 bit ADC 2. The ANAN-10EE uses an EP3C25 FPGA while the ANAN-10E uses a larger EP3C40 3. The ANAN-10EE supports 2 receivers while the ANAN-10E supports 7 receivers The ANAN-10EE is an ideal platform who want an entry level DDC/DUC SDR transceiver, performance of the rig far exceeds most high end legacy radios.


 


 


Key Features/Specifications:



  • Continuous, uninterrupted, receive coverage from 10KHz to 55MHz. .

  • Supports Real-Time display of entire sectrum from 0-55mHz (with suitable PC software)

  • Supports 7 fully independent receivers (sharing the same antenna - and with suitable PC software)

  • Each receiver can display 48/96/192/384/1152kHz of spectrum

  • Blocking Dynamic Range (ARRL Method) no detectable gain compression
    below ADC overload 

  • Transmit and receiver image rejection > 110dB

  • Full duplex operation, any split over entire 160m to 6m range.

  • Transmitter two-tone 3rd order IMD of -50dBc on 20m @ 400mW output

  • Built-in high performance preamp, with a noise floor typically -135dBm in 500H 

  • Software-selectable 31dB input attenuator in 1dB steps

  • High performance receiver – same specifications as the HPSDR Mercury receiver (ie Dynamic Range typically 125dB)

  • FPGA code can be updated via the Industry Standard TCP/IP network Ethernet connection

  • Seven user-configurable open-collector outputs, independently selectable per band and Tx/Rx (for relay control, etc - with sequencing via PC code)

  • Separate open-collector PTT connection for amplifier control, etc, with sequence 

  • Microphone PTT jumper-selectable from tip or ring connection

  • Bias for electret microphones via jumper

  • Four user-configurable 12 bit analogue inputs (for ALC, SWR etc)

  • Three user-configurable digital inputs (for linear amplifier over temperature, etc 

  • Can operate from a 13.8v DC supply or 12v and 5v supplies

  • Jumper selected in-built low noise and high efficiency switch mode power supply designed by Kjell Karson,LA2NI – less than 600mA (receive - one receiver) from a 13.8V supply

  • I2C bus connector for control of external equipment 

  • Full QSK operation (performance dependant on associated PC and control software)

  • Low-level transmitter output for transverter use via user-selectable output attenuator 

  • Stereo audio outputs at line and headphone levels

  • In-built 1W stereo audio amplifier for directly driving speakers 

  • Direct, de-bounced connections for a Morse key (straight or iambic) and PTT

  • Low phase noise (-137dBc/Hz @ 1kHz) 122.88MHz master clock, which can be phase-locked to an internal 10MHz TCXO or external fequency reference 

  • Low phase noise (-140dBc/Hz @ 1kHz at 14MHz) 122.88MHz master clock,
    which can be phase-locked to an internal 10MHz TCXO or external frequency
    reference 

  • Direct ribbon cable interface to Apollo 15W power amplifier, low pass filters and automatic ATU

  • Industry Standard TCP/IP network Ethernet interface supports static, APIPA or DHCP IP address 

  • Hermes responds to ping and ARP requests and auto senses network connection speed

  • Eight (8) Layer PCB design for the most professional, state-of-the-art, design available. 

  • Custom build rugged Extruded Housing for Hermes and the PA
    (note: no ventilation holes required in .mil style designs) 

  • Mosfet 10W Linear amplifier (160M-6M) gives 15-20W out on HF and 10-15W on 6M

  • LPFs for the PA harmonic suppression and receiver filtering 

  • Software Configurable Triple antenna ports 

  • SWR Bridge, enables Forward and Reverse Power plus SWR to be displayed using suitable PC software. 

  • T/R, LPF Switching using mechanical relays (gold plated contacts) 

  • Reverse Polarity protection with resettable fuse 

  • All cables, Hardware and instructions to make a complete transceiver with Hermes

Bar Code/EAN:
5060080576463
MPN:
No

Add your Review

You're reviewing Anan-10EE HF + 6M 10W All Mode Transceiver

Your Ratings *

Price
Value
Quality